Product Description
Technical Features
The high degree of modularity is a design feature of SRC helical gearboxes range. It can be connected respectively with motors such as normal motor, brake motor, explosion-proof motor, frequency conversion motor, servo motor, IEC motor and so on. This kind of product is widely used in drive fields such as textile, foodstuff, ceramics packing, logistics, plastics and so on. It is possible to set up the version required using flanges or feet.
Products characteristics
SRC series helical gear units has more than 4 types. Power 0.12-4kw; Ratio 3.66-54; Torque max 120-500Nm. It can be connected (foot or flange) discretionary and use multi-mounting positions according to customers requirements.
Ground-hardened helical gears;
Modularity,can be combined in many forms;
Aluminium casing, light weight;
Gears in carbonize hard, durable;
Universal mounting;
Refined design,space effective and low noise
Structure feature
Model illuminate
|
1 |
Code for gear units series |
|
2 |
No F code means foot mounted.With F code B5 flange mounted.With Z code B14 flange mounted |
|
3 |
Specification code of gear units 01 |
|
4 |
I,II,III,B5 Output flange specification,default I not to write out is ok |
|
5 |
IEC: Input flange HS: shaft input |
|
6 |
Transmission ratio of gear units |
|
7 |
M1:Mounting position, default mounting position M1 not to write out is ok |
|
8 |
Position diagram for motor terminal box,default position o°(R) not to write out is ok |
|
9 |
No mark means without motor Model motor(poles of power) |
|
10 |
Voltage – frequency |
|
11 |
Coil in position for motor, default position S not to write out is ok |
4.2 Rotation speed n
n1 Gear units input speed
n2 Gear units output speed
If driven by the external gearing,1400r/min or lower rotation speed is suggested so as to optimize the working conditions and prolong the service life.Higher input rotation speed is permitted, but in this situation,the rated torque M2 will be reduced
4.5 Service factor fs
The effect of the driven machine on the gear unit is taken into account to a sufficient level of accuracy using the service factor fs. The service factor is determined according to the daily operation time and the starting frequency Z. Three load classifications are considered depending on the mass acceleration factor. You can read off the service factor applicable to your application in following figure. The service factor selected using this diagram must be less than or equal to the service factor as given in the performance parameter table.
* starting frequency Z: The cycles include all starting and braking procedures as well as change overs from low to high speed
SRC02..(HS) Performance parameter
|
kw |
Output speed |
Torque |
Speed ratio |
fs |
Model |
IEC |
|
0.37 |
16.7rpm |
204N.M |
54 |
1.0 |
SRC02 |
80B5/B14
|
Helical gearbox outline dimension heet
| Foot Code | U | V | V1 | V2 | V3 | W | X | X1 | Y | Z |
| B02 | 18 | 107.5 | 60 | – | 130 | 11 | 136 | 155 | 100 | 17 |
| M02 | 25 | 85 | – | 110 | 120 | 9 | 112 | 145 | 80 | 15 |
| M01 | 18 | 80 | – | 110 | 120 | 9 | 118 | 145 | 80 | 15 |
| B01 | 18 | 87 | 50 | 110 | – | 9 | 118 | 130 | 90 | 15 |
SRC helical gearbox with motor mounting position and terminal box orientation
Package
1 pc / carton,several cartons / wooden pallet /* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
| Application: | Motor, Industry |
|---|---|
| Layout: | Cycloidal |
| Hardness: | Hardened |
| Samples: |
US$ 25/Piece
1 Piece(Min.Order) | Order Sample NMRV030
|
|---|
| Customization: |
Available
| Customized Request |
|---|
.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}
|
Shipping Cost:
Estimated freight per unit. |
about shipping cost and estimated delivery time. |
|---|
| Payment Method: |
|
|---|---|
|
Initial Payment Full Payment |
| Currency: | US$ |
|---|
| Return&refunds: | You can apply for a refund up to 30 days after receipt of the products. |
|---|
Calculating Torque Requirements for an NMRV Gearbox
Calculating torque requirements for an NMRV gearbox involves several steps: Identify Input Torque, Calculate Output Torque, Consider Efficiency, and Add Safety Margin.
- Identify Input Torque: Determine the input torque required by the application, taking into account factors such as load, speed, and efficiency.
- Calculate Output Torque: Use the gear ratio of the NMRV gearbox to calculate the output torque needed to achieve the desired output speed.
- Consider Efficiency: Take into account the efficiency of the NMRV gearbox. The actual output torque will be influenced by the gearbox’s mechanical efficiency.
- Add Safety Margin: To ensure reliable performance and account for variations in operating conditions, it’s recommended to add a safety margin to the calculated torque requirements.
Formula to calculate output torque: Output Torque = Input Torque × Gear Ratio × Gearbox Efficiency
Keep in mind that torque requirements can vary based on the specific application and factors such as load type, duty cycle, and environmental conditions. Consulting with gearbox manufacturers or engineering experts can help ensure accurate torque calculations for your NMRV gearbox application.
Maintenance and Service of an NMRV Gearbox
Maintaining and servicing an NMRV (worm gear) gearbox is essential to ensure its proper functioning, longevity, and reliability. Here are the steps and practices involved in maintaining and servicing an NMRV gearbox:
- Lubrication: Regularly lubricate the gearbox as per the manufacturer’s recommendations. Use the appropriate lubricant to ensure smooth operation and to reduce friction and wear between the gear components.
- Inspection: Periodically inspect the gearbox for any signs of wear, damage, or leaks. Check for unusual noises, vibrations, or overheating during operation.
- Cleaning: Keep the gearbox and its surrounding area clean to prevent the buildup of dirt, debris, or contaminants that could potentially affect its performance.
- Tighten Fasteners: Check and tighten any fasteners, bolts, or screws that might have loosened due to vibrations during operation.
- Seal Inspection: Examine the seals and gaskets for signs of wear or leakage. Replace them if necessary to prevent oil leaks or ingress of contaminants.
- Temperature Monitoring: Monitor the operating temperature of the gearbox. Excessive heat can lead to premature wear and damage. Ensure proper ventilation and cooling if required.
- Address Issues Promptly: If you notice any unusual behavior, noise, or performance issues with the gearbox, address them promptly. Ignoring problems can lead to more significant damage over time.
- Replace Worn Parts: If any components, such as gears, bearings, or seals, are worn or damaged, replace them with genuine manufacturer-approved parts.
- Professional Service: For more extensive servicing, repairs, or overhauls, consult a professional with expertise in gearbox maintenance. They can disassemble, inspect, and reassemble the gearbox accurately.
By following these maintenance and servicing practices, you can ensure that your NMRV gearbox remains in optimal condition, delivering reliable performance and an extended operational lifespan.
NMRV Gearbox Ratios
NMRV gearboxes are available in a variety of gear ratios to suit different applications and torque requirements. The gear ratio determines the relationship between the input and output speeds of the gearbox. Commonly available ratios include:
- 5:1: This ratio provides higher output torque at a slower output speed compared to the input speed.
- 7.5:1: This ratio offers a balance between torque and speed.
- 10:1: With this ratio, the output speed is further reduced while increasing torque output.
- 15:1: This ratio is suitable for applications requiring higher torque output at the expense of speed.
- 20:1: This ratio maximizes torque output while significantly reducing output speed.
- 25:1: It provides even higher torque output at a further reduced output speed.
- 30:1: This ratio is ideal for applications demanding maximum torque at minimum output speed.
- 40:1 and higher: These ratios are used in applications with very high torque requirements and low output speed.
The choice of gearbox ratio depends on the specific application, desired output speed, and required torque. It’s important to select the right ratio to ensure optimal performance and efficiency in your machinery.
editor by CX 2024-05-03